| Parameter | Associated MIB variable |
Description |
| BIA | cfmff100BiaIndex(1) | See BIA and Slot |
| Slot | cfmff100SlotIndex(2) | See BIA and Slot |
| Group Membership | cfmff100Groups(3) | See Configuration Management |
| Marketing Revision | cfmff100MRevision(4) | Marketing Revision |
| Config Match | cfmff100CfgMatch(5) | Configuration Management match? |
| Singlemode Fiber Connector or Interface 1 socket | cfmff100ConnA(6) | Built-in Connector Type reported by device |
| Multimode Copper Connector or Interface 2 socket | cfmff100ConnB(7) | Built-in Connector Type reported by device |
| Serial Number | cfmff100SerialNumber(8) | Serial Number reported by hardware |
| Multimode Signal Detect | cfmff100SMSignal(9) | Signal Detect status of Multimode Fiber Port |
| Singlemode Signal Detect | cfmff100MMSignal(10) | Signal Detect status of Singlemode Fiber Port |
| Enabled | cfmff100Enabled(11) |
Disable one or both ports of the device, causing it to stop passing traffic.
On retiming versions of the device (such as marketing revision 280),
link may be maintained on one interface while dropping it on the other
by disabling only one interface (by setting value noP1(2) or noP2(3)).
No traffic passes in either direction.
On other versions, there is no functional
difference between disabling one interface and disabling both.
Values: yes(1), noP1(2), noP2(3), no(4)
|
| Port Shutoff | cfmff100PortShutOff(12) | Port Shutoff configuration |
| Configuration Mode | cfmff100ConfigMode(13) | Configuration Mode |
| Cache Clean | cfmff100CacheClean(14) | Configuration changes pending? |
| Full Duplex | cfmff100FullDuplex(15) |
When cfmff100AutoNegot(18) is enabled(1), this variable controls the advertising of Full Duplex mode on both interfaces. Half Duplex advertisements are sent whenever Autonegotiation is enabled.
Possible values are:
enabled(1), disabled(2)
and, for older CFMFF100 devices, NotSupported(3).
|
| Link Passthrough | cfmff100LinkPassThrough(16) |
This variable allows Link Passthrough mode to be enabled or disabled.
Possible values are:
enabled(1), disabled(2)
and, for older CFMFF100 devices, notSupported(3), which
indicates that management of Link Passthrough is unsupported.
For these devices, Link Passthrough itself is always in effect.
|
| Pause | cfmff100AdvPause(17) | This variable controls the advertising of Pause on both interfaces.
Possible values are
SymmAsymRX(1), Symmetric(2),
SymmetricRX(3),
Disabled(4),
and, for older CFMFF100 devices, NotSupported(5).
|
| Autonegotiation | cfmff100AutoNegot(18) | This variable controls Autonegotiation advertisements on both interfaces.
Possible values are:
enabled(1), disabled(2)
and, for older CFMFF100 devices, NotSupported(3).
|
| Receive Power | cfmff100ADmiRxPower(19) |
Interface 1 optical receive power.
See DMI
|
| Receive Power Alarm | cfmff100ADmiRxPowerAlarm(20) |
Alarm status of interface 1 optical receive power.
See DMI
|
| Temperature | cfmff100ADmiTemp(21) |
Internally measured temperature of interface 1.
See DMI
|
| Temperature Alarm Status | cfmff100ADmiTempAlarm(22) |
Internally measured temperature of interface 1.
See DMI
|
| Transmit Bias Currrent Alarm Status | cfmff100ADmiTxBiasAlarm(23) |
Alarm status for measured transmit bias current for interface 1.
See DMI
|
| Transmit Bias Currrent | cfmff100ADmiTxBiasCurrent(24) |
Measured transmit bias current for interface 1.
See DMI
|
| Transmit Power | cfmff100ADmiTxPower(25) |
Measured transmit power for interface 1.
See DMI
|
| Transmit Power Alarm Status | cfmff100ADmiTxPowerAlarm(26) |
Alarm status for measured transmit power for interface 1.
See DMI
|
| Intrusion Threshold | cfmff100ADmiRxPowerThreshold(27) |
Receive power intrusion threshold for interface 1.
See DMI
|
| Module Type | cfmff100ADmiConnectorType(28) |
Socketed Media Connector Module Type for interface 1.
See DMI
|
| Nominal Bit Rate | cfmff100ADmiBitRate(29) |
Bit rate for interface 1.
See DMI
|
| Supported Media Length, 9/125µ Singlemode Fiber | cfmff100ADmiLenSupp9125(30) |
Supported length of 9/125µ Singlemode Fiber on interface 1.
See DMI
|
| Supported Media Length, 50/125µ Multimode Fiber | cfmff100ADmiLenSupp50125(31) |
Supported length of 50/125µ Multimode Fiber on interface 1.
See DMI
|
| Supported Media Length, 62.5/125µ Multimode Fiber | cfmff100ADmiLenSupp625125(32) |
Supported length of 62.5/125µ Multimode Fiber on interface 1.
See DMI
|
| Supported Media Length, Copper | cfmff100ADmiLenSuppCopper(33) |
Supported length of copper on interface 1.
See DMI
|
| Fiber Interface Wavelength | cfmff100ADmiWavelength(34) |
Transceiver wavelength for interface 1.
See DMI
|
| Socket Type | cfmff100ADmiIdent(35) |
Transceiver socket type for interface 1.
See DMI
|
| Receive Power | cfmff100BDmiRxPower(36) |
Interface 2 optical receive power.
See DMI
|
| Receive Power Alarm | cfmff100BDmiRxPowerAlarm(37) |
Alarm status of interface 2 optical receive power.
See DMI
|
| Temperature | cfmff100BDmiTemp(38) |
Internally measured temperature of interface 2.
See DMI
|
| Temperature Alarm Status | cfmff100BDmiTempAlarm(39) |
Alarm status for internally measured temperature of interface 2.
See DMI
|
| Transmit Bias Currrent Alarm Status | cfmff100BDmiTxBiasAlarm(40) |
Alarm status for measured transmit bias current for interface 2.
See DMI
|
| Transmit Bias Currrent | cfmff100BDmiTxBiasCurrent(41) |
Measured transmit bias current for interface 2.
See DMI
|
| Transmit Power | cfmff100BDmiTxPower(42) |
Measured transmit power for interface 2.
See DMI
|
| Transmit Power Alarm Status | cfmff100BDmiTxPowerAlarm(43) |
Alarm status for measured transmit power for interface 2.
See DMI
|
| Intrusion Threshold | cfmff100BDmiRxPowerThreshold(44) |
Receive power intrusion threshold for interface 2.
See DMI
|
| Module Type | cfmff100BDmiConnectorType(45) |
Socketed Media Connector Module Type for interface 2.
See DMI
|
| Nominal Bit Rate | cfmff100BDmiBitRate(46) |
Bit rate for interface 2.
See DMI
|
| Supported Media Length, 9/125µ Singlemode Fiber | cfmff100BDmiLenSupp9125(47) |
Supported length of 9/125µ Singlemode Fiber on interface 2.
See DMI
|
| Supported Media Length, 50/125µ Multimode Fiber | cfmff100BDmiLenSupp50125(48) |
Supported length of 50/125µ Multimode Fiber on interface 2.
See DMI
|
| Supported Media Length, 62.5/125µ Multimode Fiber | cfmff100BDmiLenSupp625125(49) |
Supported length of 62.5/125µ Multimode Fiber on interface 2.
See DMI
|
| Supported Media Length, Copper | cfmff100BDmiLenSuppCopper(50) |
Supported length of copper on interface 2.
See DMI
|
| Fiber Interface Wavelength | cfmff100BDmiWavelength(51) |
Transceiver wavelength for interface 2.
See DMI
|
| Socket Type | cfmff100BDmiIdent(52) |
Transceiver socket type for interface 2.
See DMI
|