Media Conversion, Switching and Data Networking by Transition Networks

10/100BASE-TX to 100BASE-FX
Remotely Managed 10/100 Bridging NID

CSFRB-10xx-100

Ideal for both Enterprise and Service Provider applications were entry level management information is needed on both the local and the remote device. This management information of remote unit is accessible through the local unit installed in a managed Point System Chassis.
Devices should be used in pairs with the remotely located device being another chassis card (CSRFB10xx-100) or a stand-alone unit (SSRFB10xx-100).

Data Sheet [PDF]

Installation Manual [PDF]

Features

Applications

Specifications

Ordering Information

Auto-Negotiation (802.3u)
Allows devices to perform automatic configuration to achieve the best possible mode of operation over a link.
AutoCross™
Automatically detects and configures the twisted pair port on the converter to the correct MDI or MDI-X configuration.
Far End Fault (FEF)
A troubleshooting feature that is generally used in conjunction with Link Pass Through to notify both end devices of a loss of link.
Transparent Link Pass Through
Transparent Link Pass Through sends a link-loss signal over the fiber, instructing the remote converter to shut down the copper port—thus notifying the end device—while maintaining the fiber link between the two converters.
Bandwidth Allocation
An important feature found on select converters which allows network administrators to set the bandwidth of the converter to 64KB increments via SNMP management.
Loopback
This feature puts a converter in a special mode that enables the device to loop back the signal from the RX port to the TX port on either media for testing and troubleshooting purposes.
Last Gasp
This feature enables the device to store a small amount of power to enable it to send out an SNMP trap to alert the management console in the event of a power failure.
Remote Management
Select stand-alone converters can be managed through SNMP when used in conjunction with a chassis based converter.
Automatic Link Restoration
Transition Networks's converters will automatically re-establish link in all network conditions.
Remote Firmware Upgrade
Link Test

Status Reporting Capabilities:

Last Gasp power failure of remote unit

Copper Link Status of local and remote unit

Copper Speed Status of local and remote units

Ingress rate limiting on local unit

Fiber Link Status of local and remote units

Fiber Duplex of local and remote units

Fiber Loop Back status of remote unit

AutoCross status of local and remote units

Hardware or Software mode status of local and remote units

Central or Terminal mode status of local and remote units

Standards	IEEE Std. 802.3, TS-1000 OAM v2
Data Rate	Copper: 10/100 Fiber: 100 Mbps
Filtering Addresses	1K MAC addresses
RAM Buffers	256K
Max Frame Size	1916 bytes untagged 1914 bytes tagged
Switches	SW1: TP Auto-Negotiation SW2: TP Duplex with Auto-Negotiation Off SW3: TP Speed with Auto-Negotiation Off SW4: Fiber Duplex SW5: Link Pass Through SW6: Mode: Terminal or Center
Status LEDs	Power TP Duplex/Link/Activity TP 10Mbps/100Mbps Fiber Link/Activity Fiber Duplex
Dimensions	Width: 3.25” (82mm) Depth: 4.8” (122mm) Height: 1.0” (25mm)
Power Consumption	3.4 watts
Environment	0 – 50 C; 5% - 95% humidity non-condensing; 0 – 10,000 feet altitude
Power	External AC/DC required; 12VDC 1.25A
Shipping Weight	2 lbs. (.90 kg)
Safety Compliance	Wall Mount Power Supply: UL Listed and CSA certified
Regulatory Compliance	EN55022 Class A, EN55024; CE Mark
Warranty	Lifetime

10/100BASE-TX to 100BASE-FX Remotely Managed 10/100 Bridging NID

Features

Applications

Specifications

Ordering Information

10/100BASE-TX to 100BASE-FX
Remotely Managed 10/100 Bridging NID